*2013/12/16 15:19:15.88 *IOS HEADER VERSION 1.10 2011/10/26 2011/10/26 *COMMENTS Alt S start 01:44:29 10-15-1999 GPS not used. Alt S stop 01:49:02 10-15-1999 CTDEDIT was used to clean salinity from 31.6-40.5db. This was to remove an unstable feature that was found at casts where sharp transitions occurred between well-mixed layers; it appears to be instrumental in nature. *FILE START TIME : UTC 1999/10/15 01:44:29.250 END TIME : UTC 1999/10/15 01:49:02.280 NUMBER OF RECORDS : 123 DATA DESCRIPTION : CTD FILE TYPE : ASCII NUMBER OF CHANNELS : 4 $TABLE: CHANNELS ! No Name Units Minimum Maximum !--- ----------------------- ---------------- -------------- -------------- 1 Pressure decibar 0.57 61.49 2 Temperature 'deg C (IPTS68)' 3.2761 6.3315 3 Salinity PSS-78 32.0252 32.3155 4 Number_of_bin_records n/a 2 9 $END $TABLE: CHANNEL DETAIL ! No Pad Start Width Format Type Decimal_Places !--- ---- ----- ----- ------ ------ -------------- 1 -99 ' ' 8 F ' ' 2 2 -99 ' ' 9 F ' ' 4 3 -99 ' ' 9 F REAL*4 4 4 -99 ' ' 5 I I 0 $END $REMARKS File name : 99250047.ACQ $END *ADMINISTRATION MISSION : 1999-25 AGENCY : IOS, Ocean Science and Productivity, Sidney, B.C. COUNTRY : Canada PROJECT : Arctic99 SCIENTIST : van Hardenburg B. PLATFORM : Sir Wilfrid Laurier *LOCATION GEOGRAPHIC AREA : Arctic Archipelago STATION : BS7 EVENT NUMBER : 47 LATITUDE : 58 31.47000 N ! (deg min) LONGITUDE : 169 22.20000 W ! (deg min) LATITUDE 2 : 58 31.47000 N ! (deg min) LONGITUDE 2 : 169 22.20000 W ! (deg min) WATER DEPTH : 69 $REMARKS Station Latitude : 58 31.50 N Longitude : 169 22.00 W Depth : 70 $END *INSTRUMENT TYPE : Guildline Guildn CTD MODEL : Arctic SERIAL NUMBER : 43825 $REMARKS Acquisition program : CTD.EXE version 1.45 CTD data type : 2 ! 8755 system binary frame Control String : KP1000TC4 $END *RAW START TIME : UTC 1999/10/15 01:44:29.250 END TIME : UTC 1999/10/15 01:49:02.280 TIME INCREMENT : 0 0 0 0 40 ! (day hr min sec ms) NUMBER OF RECORDS : 6598 $TABLE: CHANNELS ! Averaging (day hr min sec ms) !Name Raw Units Interval Time Lag !-------------------- --------------- --------- ----------- Pressure Percent_FS Temperature 'DEG C (ITS68)' Conductivity_Ratio n/a Transmissivity Percent_FS $END *CALIBRATION $TABLE: RAW CHANNELS ! Name Units Fmla Pad Coefficients ! -------------------- --------------- ---- ------ ------------ Pressure dBars 10 -99 (-8.47 1007.609 -10.14 6.934) Temperature 'DEG C (ITS68)' 10 -99 (-0.23E-04 1.0004) Conductivity_Ratio n/a 63 -99 (-0.871E-03 1.001) Transmissivity '%/25 cm' 10 n/a (112.23 -2.24675) $END $TABLE: CALCULATED CHANNELS ! Name Units Fmla Pad Coefficients ! ---------- -------- ---- ------ ------------ Salinity PSS-78 130 -99 (Pressure Temperature Conductivity_Ratio) () $END $TABLE: CORRECTED CHANNELS ! Name Units Fmla Pad Coefficients ! ---------- ----- ---- ------ ------------ Pressure db 10 -99 () (0.5 1) Salinity psu 10 -99 () (-0.14E-01 1) $END *HISTORY $TABLE: PROGRAMS ! Name Vers Date Time Recs In Recs Out ! ------------------------ ------ ---------- -------- --------- --------- ACQCONV 2.02 2000/04/04 12:16:27 6598 6598 CALIB 8.4 2000/04/04 13:17:08 6598 6598 VIEW 5.02 2000/05/11 09:07:37 6598 6598 VIEW 5.02 2000/05/15 15:41:25 6598 6598 CLEAN 2.8.2 2000/05/15 15:50:21 6598 6598 DERIVEDQ 2.3 2000/05/15 15:50:41 6598 6598 VIEW 5.02 2000/05/15 16:06:32 6598 6598 CLEAN 2.8.2 2000/05/15 16:06:49 6598 6598 DERIVEDQ 2.3 2000/05/15 16:06:55 6598 6598 DELETE 4.4 2000/05/16 14:42:10 6598 703 BOXCAR 4.1 2000/05/16 16:49:10 703 703 CTDEDIT 4.16 2000/05/19 11:23:44 703 703 BINAVE 3.0 2000/05/19 17:07:41 703 123 CALIB 8.9 2000/05/19 17:08:46 123 123 REMOVECH 4.0 2000/05/19 17:10:47 123 123 REMOVECH 4.0 2000/05/26 09:26:59 123 123 HDREDIT2 1.9 2004/01/15 11:24:44 ? ? CLEAN 4.5 2004/01/15 11:25:31 123 123 CHANGE_CTD_CHANNEL_NAMES 1.0 2013/12/16 15:19:15 123 123 $END $REMARKS -The following CALIB parameters were used: Calibration type = Raw Salinity is computed Pressure offset = 0.0 Calibration file = M:\Data\9923\Gld\ios\9923cal.ccf Calibration file summary: 2000/04/04 13:12:46.68 Specifications for files ranging from *** to ***, using MODE: 'UNION'. Name Units Fmla Coefficents ------------------------- ------------- ---- ------------------------------ Pressure 10s -0.8470000E+01 0.1007609E+04 -0.1014000E+02 0.6934000E+01 Salinity 130 0.0000000E+00 0.0000000E+00 Pressure Temperature Conductivity_Ratio Temperature 10C -0.2300000E-04 0.1000400E+01 Conductivity_Ratio 63 -0.8710000E-03 0.1001000E+01 End of Calibration file summary: CLEAN functions: - Reset #RECS, MIN & MAX values in header. -The following DERIVEQ parameters were used Reference channel for pressure is: Pressure Reference channel for temperature is: Temperature Reference channel for conductivity ratio is: Conductivity_Ratio Reference channel for salinity is: Salinity Computed properties Derived Properties Ref Press Temp Type Replace ------------------ --------- --------- ------- Salinity Insitu Insitu YES CLEAN functions: - Reset #RECS, MIN & MAX values in header. -The following DERIVEQ parameters were used Reference channel for pressure is: Pressure Reference channel for temperature is: Temperature Reference channel for conductivity ratio is: Conductivity_Ratio Reference channel for salinity is: Salinity Computed properties Derived Properties Ref Press Temp Type Replace ------------------ --------- --------- ------- Salinity Insitu Insitu YES -The following DELETE parameters were used: Surface Record Removal: Last Press Min Maximum Surface Pressure (relative): 20.00 Surface Swell Pressure Tolerance: 0.50 Pressure NOT filtered Swells deleted. Warning message if pressure difference of 2.00 Drop rates< 0.30m/s (calculated over 15 points) will be deleted Sample interval = 0.04 seconds. -The following FILTER parameters were used. Boxcar filter was used. Filter width = 21 The following channel(s) were filtered. Salinity -The following BINAVE parameters were used: Bin channel = Pressure Averaging interval = 0.5 Minimum bin value = 0.000 Average value was used Interpolated values were NOT used for empty bins Channel 'NUMBER_OF_BIN_RECORDS' was added to file. -The following CALIB parameters were used: Calibration type = Correct Mode: ONLY - calibration specs from Cal File only. Pressure offset = 0.0 Calibration file = W:\CTD\9925\9925rcal.ccf Calibrations applied: Ch Name Units Fmla Coefficents -- ----------------------------- --------- --- ----------------------------- 1 Pressure db 10 0.5000000E+00 0.1000000E+01 5 Salinity psu 10 -0.1400000E-01 0.1000000E+01 -The following CHANNEL(S) were removed from file. Conductivity_Ratio -The following CHANNEL(S) were removed from file. Transmissivity CLEAN functions: - Reset #RECS, MIN & MAX values in header. - Change Pad Value to -99 in All Channels. $END !---1--- ---2---- ---3---- -4-- !Pressur Temperat Salinity Numb !e ure er_o ! ~bin ! _rec ! ords !------- -------- -------- ---- *END OF HEADER 0.57 6.3315 32.0252 2 0.99 6.3204 32.0272 4 1.48 6.3121 32.0274 4 2.02 6.3188 32.0282 6 2.57 6.3090 32.0284 4 3.05 6.2990 32.0291 7 3.55 6.2969 32.0284 6 3.98 6.2926 32.0278 4 4.47 6.2931 32.0275 4 4.98 6.2933 32.0270 5 5.53 6.2930 32.0269 4 5.96 6.2926 32.0268 4 6.52 6.2925 32.0273 6 7.04 6.2923 32.0275 6 7.47 6.2917 32.0275 8 7.97 6.2921 32.0270 7 8.49 6.2920 32.0268 4 8.98 6.2922 32.0270 4 9.48 6.2924 32.0271 7 10.01 6.2924 32.0271 3 10.50 6.2924 32.0271 5 11.03 6.2925 32.0270 4 11.47 6.2924 32.0271 5 12.07 6.2923 32.0272 5 12.51 6.2922 32.0274 6 13.00 6.2922 32.0277 7 13.49 6.2923 32.0274 8 14.01 6.2935 32.0273 6 14.45 6.2938 32.0271 5 15.01 6.2940 32.0269 4 15.47 6.2941 32.0268 4 15.97 6.2940 32.0266 4 16.51 6.2933 32.0265 6 17.02 6.2931 32.0266 4 17.51 6.2931 32.0270 6 18.01 6.2930 32.0275 4 18.44 6.2929 32.0277 6 19.00 6.2932 32.0279 8 19.47 6.2932 32.0279 7 19.99 6.2931 32.0277 5 20.51 6.2934 32.0275 5 21.05 6.2935 32.0273 5 21.44 6.2933 32.0273 4 21.98 6.2936 32.0274 6 22.47 6.2945 32.0275 6 23.02 6.2919 32.0272 4 23.47 6.2939 32.0272 5 23.95 6.2945 32.0279 6 24.48 6.2908 32.0285 6 24.98 6.2894 32.0291 6 25.49 6.2923 32.0295 5 25.96 6.2933 32.0292 5 26.41 6.2943 32.0294 5 27.02 6.2928 32.0301 6 27.52 6.2923 32.0320 6 27.99 6.2641 32.0349 6 28.49 6.2544 32.0379 6 28.98 6.2527 32.0398 6 29.54 6.2493 32.0417 5 29.99 6.2386 32.0491 6 30.53 6.1586 32.0774 5 31.00 6.0037 32.1280 4 31.49 5.5954 32.1958 4 31.99 4.5570 32.2857 7 32.53 3.4772 32.3116 6 32.99 3.3803 32.3117 4 33.48 3.3134 32.3119 5 34.00 3.2836 32.3121 7 34.52 3.2828 32.3122 6 35.01 3.2832 32.3124 6 35.50 3.2828 32.3125 8 35.97 3.2836 32.3127 3 36.45 3.2854 32.3129 6 36.97 3.2830 32.3130 5 37.43 3.2807 32.3132 7 38.00 3.2789 32.3134 5 38.46 3.2808 32.3135 6 38.98 3.2794 32.3137 6 39.52 3.2771 32.3139 6 39.97 3.2772 32.3140 7 40.51 3.2778 32.3142 6 40.95 3.2785 32.3147 4 41.49 3.2781 32.3155 6 42.00 3.2775 32.3148 7 42.54 3.2774 32.3144 6 43.00 3.2772 32.3142 3 43.47 3.2771 32.3141 6 43.95 3.2773 32.3139 5 44.50 3.2765 32.3135 6 45.02 3.2765 32.3130 8 45.51 3.2768 32.3124 7 45.96 3.2770 32.3119 5 46.54 3.2772 32.3116 6 47.02 3.2773 32.3115 4 47.51 3.2773 32.3114 6 48.02 3.2773 32.3111 4 48.51 3.2774 32.3111 6 49.04 3.2773 32.3111 6 49.50 3.2771 32.3115 6 49.97 3.2772 32.3122 6 50.47 3.2773 32.3126 8 51.04 3.2770 32.3125 7 51.46 3.2771 32.3124 5 51.92 3.2775 32.3123 6 52.50 3.2775 32.3122 6 52.99 3.2777 32.3121 5 53.49 3.2781 32.3121 4 53.92 3.2790 32.3121 6 54.45 3.2784 32.3123 7 54.97 3.2781 32.3126 8 55.49 3.2787 32.3123 7 55.96 3.2786 32.3117 7 56.53 3.2794 32.3112 8 57.02 3.2794 32.3110 8 57.47 3.2786 32.3111 8 57.97 3.2785 32.3111 7 58.49 3.2785 32.3114 9 59.02 3.2785 32.3120 7 59.51 3.2772 32.3124 8 60.01 3.2773 32.3120 8 60.56 3.2775 32.3112 7 61.02 3.2780 32.3110 8 61.49 3.2761 32.3114 6